With 4 Outputs
ESP32 WLED Digital LED Controller
– User Instruction –
GL-C-017WL-D

Parameter produk

Model: GL-C-017WL-D
Total Output Saiki: 15A Max
Ukuran: 108 x 45 x 18 mm
Vol inputtage: DC 5-12-24V
Protokol: WiFi
Suhu: -20~45°C

Wiring Terminal Instructions

1. The WLED controller can support a total of 4 output channels. The output terminal connections “V GND GPIO16 GPIO12 GPIO4 GPIO2” correspond to the “VCC DATA GND” pins of the digital LED strips.
2. IO13 is an extended GPIO signal port for custom use.

Metode Unduh APLIKASI

IOS

1. Nggoleki and download WLED Native in the App Store.
   Android
   Nggoleki and download WLED Native in the Google Play Store.
   

Langkah Konfigurasi APP

1. Daya ing controller WLED.
2. Open the phone settings and enter WiFi settings, find “WLED-AP” and connect to it with the password “wled1234”.
   
3. Sawise sambungan sukses, bakal kanthi otomatis mlumpat menyang kaca WLED (utawa ketik websitus 4.3.2.1 ing browser kanggo ngetik kaca WLED).
   
4. Click “WIFI SETTINGS”, set the WiFi account and password, and the click “Save & Connect” at the top of the screen to save.
   
5. Keep both your phone and the WLED controller connected to the same Wi-Fi network. Then, open the WLED-Native APP, and the WLED controller will be displayed in the list.
   

Cathetan:

1. After the WLED controller disconnects from the router, the chip will restart and return to the preset state (you can find the hotspot “WLED-AP” in your phone’s WiFi settings).
2.  If the WLED controller is not displayed or cannot be found in the APP, you can open a browser, enter the IP address of the WLED controller, and use the web interface for control (To find the controller’s IP address: Connect to the Wi-Fi, locate the router’s or controller’s web address (usually found at the bottom of the router or on the controller itself), enter this address in the browser, and then you can view the controller’s IP address in the router’s backend interface).

Konfigurasi Strip LED

Enter into the WLED control page and click on the “Config” button in the upper right corner. Then, select “LED Preferences” and navigate to “Hardware setup” to configure the LED strip information.

Konfigurasi Relay

Enter into the WLED control page, click on the top right corner “Config”, select “LED Preferences”, then find “Relay GPIO”.
Configure Relay GPIO as 18, check Invert, and click Save to apply the settings.

Cathetan:

1. The relay function is configured by default.
2.  When turning off the light via the APP, remote control, or PUSH switch, the power supply to the output terminal will be cut off to save energy. It should be noted that this function cannot deactivate the supplementary power supply.

Konfigurasi Mic

Enter the WLED control page, click “config” in the upper right corner, select “Usermods”, find “Audio Reactive”, check (Enabled), and then configure according to the configuration information under “Digitalin”. After the configuration is completed, click “save”. After the successful save, turn off the controller.
Informasi Konfigurasi:

1. Type: Generic 12S PDM
2. Pin 12S SD: 32
3. Pin 12S WS: 15
   

Cathetan:

1. The Mic function is configured by default.
2. After microphone function configured, it will be only activated after rebooting the controller again.

Deskripsi Fungsi Tombol

Wiwiti maneh:
Pressing the button will power off the controller module, releasing it will power it back on. Useful when the controller needs to be restarted after configuring the microphone.
Functions (GPIO17):

1. Pencet cendhak: Power on/off.
2. Pencet dawa kanggo 1 detik: Ganti werna.
3. Pencet suwene 10 detik: Reset pengontrol WLED lan aktifake hotspot WLED-AP.

Reset menyang Setelan Pabrik

1. Tombol Reset
   Long press the “Function” button for 10 seconds.
2. APP Reset
   Enter into the WLED control page and click on the top right corner “Config”.
   Click on “Security & Updates” at the bottom, and then scroll down to find “Factory reset” and check the box. Click “Save” to reset the controller.

UART Download

1. Remove the power supply and light strip.
2. Copot omah.
3. Connect the Type-C cable and start downloading.

Didhukung Kripik

WS2805, WS2811, WS2811F, WS2812B, WS2814A, WS2815, SK6812, SM16703, SM16703SP3, FL19038, FW1935, UCS2903B, lsp.

Ngatasi masalah lan Solusi

Nomer	Gejala	Solusi
1	Lampu indikator ora urip	Check whether the input power connection is correct
2	APP nuduhake "offline"	1. Priksa manawa telpon ana ing jaringan sing padha karo pengontrol. 2. Priksa manawa controller metu saka jangkauan sambungan WIFI, nyebabake sambungan ora stabil. 3. Pateni lan ing controller kanggo nyoba maneh.
3	APP disambungake, nanging jalur cahya ora bisa dikontrol	1. Check if the power supply is working properly. 2. Priksa yen sumber daya voltage cocog karo strip cahya. 3. Priksa manawa sambungan daya input wis bener. 4. Priksa manawa sambungan strip lampu wis bener. 5. Priksa manawa setelan GPIO ing APP wis bener. 6. Priksa manawa model IC strip cahya ing APP disetel kanthi bener.
4	Cahya jalur cahya kurang, lan werna ngarep lan mburi beda banget	1. Priksa manawa sumber daya bisa digunakake kanthi bener. 2. Priksa manawa sumber daya cocog karo jalur lampu. 3. Priksa yen kabeh sambungan apik, lan nggunakake kabel konduktif lan cendhak sabisa kanggo sambungan. 4. Tambah sumber daya ing posisi cocok. 5.  Check if the APP has set a limit on brightness or current.

1. Before turning on the power, please ensure that all connections are correct
   and secure, and do not operate while the power is on.
2. Prodhuk kudu digunakake miturut nilai voltage. Nggunakake ing volume sing berlebihan utawa ora cukuptage bisa nyebabake karusakan.
3. Aja mbongkar prodhuk, amarga bisa nyebabake geni lan kejut listrik.
4. Aja nggunakake produk ing lingkungan sing kena sinar srengenge langsung, kelembapan, suhu dhuwur, lsp.
5. Aja nggunakake prodhuk ing wilayah sing dilindhungi logam utawa ing sekitar medan magnet sing kuwat, amarga bisa nyebabake transmisi sinyal nirkabel produk kasebut.

Penafian

1. Perusahaan kita bakal nganyari isi manual iki adhedhasar perbaikan fungsi produk. Nganyari bakal ditampilake ing versi paling anyar saka manual iki, tanpa kabar luwih.
2. Amarga nggunakake teknologi anyar sing terus-terusan, spesifikasi produk bisa uga diganti tanpa kabar.
3. Manual iki diwenehake mung kanggo referensi lan panuntun dhumateng lan ora njamin konsistensi lengkap karo produk nyata. Aplikasi nyata kudu adhedhasar produk nyata.
4. Komponen lan aksesoris sing diterangake ing manual iki ora makili konfigurasi standar produk. Konfigurasi tartamtu tundhuk ing kemasan.
5. Kabeh teks, tabel, lan gambar ing manual iki dilindhungi dening hukum nasional sing relevan lan ora bisa digunakake tanpa idin kita.
6. This product may be compatible with third-party products, but our company does not take responsibility for compatibility issues or partial loss of functionality caused by changes in third-party products.

GL-C-I-017WL(PDM)

Dokumen / Sumber Daya

SUPERLIGHTINGLED GL-C-017WL-D 4 Outputs ESP32 WLED Digital LED Controller [pdf] Manual pangguna GL-C-017WL-D 4 Outputs ESP32 WLED Digital LED Controller, GL-C-017WL-D, 4 Outputs ESP32 WLED Digital LED Controller, ESP32 WLED Digital LED Controller, WLED Digital LED Controller, Digital LED Controller, LED Controller

Referensi

• Manual pangguna