Lumens OIP-N60D Signal Distribution IP Distribution
Spesifikasi Produk
- Jeneng produk: OIP-N60D TV Wall
- Fungsi: Multiple screen splicing for large display
- Maximum TV Wall Configuration: 3X3
- Unit pangukuranJembar: 0.1 mm
- Dhukungan: Lumens technical support team
Pandhuan Panggunaan Produk
- Step 1: Set Layout Mode
Go to [Layout] and change the [Layout Model] to [TV Wall]. - Step 2: Set up Bezel and Gap Compensation
To ensure continuous display, fill in the Overall Width/Height and Video Width/Height in 0.1mm units. For example, if OW is 100cm, input 10000. - Step 3: Set up TV Wall Amount and OIP-N60D Position
Enter the TV Wall amount (up to 3X3) and specify the OIP-N60D position (e.g., A1, B2, C3). - Step 4: Select Video Source on OIP-N60D
Go to [Source] and choose the desired video source to play. - Step 5: Repeat Steps 1-4 for other OIP-N60D
Akses menyang webpage of other OIP-N60D devices and repeat Steps 1-4. Adjust parameters as needed for each device.
Dhukungan
For installation or configuration assistance, please contact Lumens’ technical support team.
Pambuka
TV Wall is one of the functions in OIP-N60D. It is used in applications with multiple screen splicing. By connecting an OIP-N to each screen and outputting the same video source, multiple screens can be spliced together to form a large display. The diagram below illustrates the application.
Apa Sampeyan Perlu
- OIP-N60D/OIP-N60D, Dante AV-H 2-9 units
- OIP-N60D: FW OIB119 above
- OIP-N60D Dante AV-H: FW OIC115 above
- OIP-N40E x 1 unit (FW OIA119 above) or IP Video Source X1
Recommendations and Limitations Before Setup
- Connect all devices to the same LAN where possible
- Record each OIP’s IP address and corresponding display position
- Maximum supported configuration: 3×3 (9 units)
- Output supports landscape only (portrait mode not supported)
- Recommended layout: 2×2 or 3×3 for proper aspect ratio; other layouts may cause distortion
- Virtual USB output not supported
Set up for TV Wall
- Step 1: Set Layout Mode
Go to [Layout] → Change [Layout Model] to [TV Wall]
- Step 2: Set up Bezel and Gap Compensation
To avoid the TV Wall not being continuous from the display gap, the user should fill in below data: Overall Width/Height, and Video Width/Height.
Unit: 0.1mm, for example: When OW is 100cm, the user should fill in 10000(0.1mm).
- Step 3: Set up the TV Wall amount and the OIP-N60D position
Fill in TV Wall amount (Maximum 3X3), and OIP-N60D position (e.g., A1, B2, C3 …).- Horizontal Monitor Count – Number of displays per row
- Vertical Monitor Count – Number of displays per column
- Horizontal Position – Column position (A, B, C)
- Vertical Position – Row position (1, 2, 3)
Tip: Keep a record of each OIP-N’s IP and display position for troubleshooting and future adjustments.
- Step 4: Select Video source on OIP-N60D
GO to [Source] →Select the video source you want to play.
- Step 5: Repeat Step1-4 in the other OIP-N60D
Go to the other OIP-N60D webpage and repeat Step1-Step4, Step 2 ,and Step 3 should modify parameters depending on the different OIP-N60D.
Dhukungan
For installation or configuration support, please contact Lumens’ technical support team to assist.
Pitakonan sing Sering Ditakoni
What is the maximum TV Wall configuration supported?
The maximum TV Wall configuration supported is 3X3.
How do I set up Bezel and Gap Compensation?
Fill in the Overall Width-Height and Video Width-Height in 0.1mm units to ensure continuous display.
Dokumen / Sumber Daya
 |
Lumens OIP-N60D Signal Distribution IP Distribution [pdf] Instruksi Manual OIP-N60D, OIP-N40E, OIP-N60D Signal Distribution IP Distribution, OIP-N60D, Signal Distribution IP Distribution, Distribution IP Distribution |