KMC CONTROLS STE-9000 series NetSensor Damage from Incorrect
Spesifikasi
- Product: STE-9000 series NetSensor
- Features: Temperature and humidity readings
- Model: All STE-9000 series NetSensors
Pandhuan Panggunaan Produk
- Ensure that both tabs on the sensor cover rest on top of the backplate.
- Make sure the anti-tamper hex screw is fully rotated into the backplate before installing or uninstalling the sensor cover.
- Swing the cover from the top onto the backplate.
- Do NOT push the cover directly onto the plate or swing it from the bottom.
- If any force seems to be needed, check the alignment of the tabs on the top of the backplate and/or the anti-tamper screw before swinging the sensor cover onto the backplate.
- For more detailed installation instructions, please refer to the STE-9000 Series NetSensors Installation Guide.
Rampungake langkah-langkah ing ngisor iki kanggo masang KMC Conquest STE-9000 Series Digital NetSensor lan nyambungake menyang Conquest BAC-59xx / 9xxx Controller.
CATETAN: Waca Conquest NetSensors STE- 9000 Series Digital Room Sensors lembar data lan Pandhuan Seleksi Penaklukan at kmccontrols.com for specifications and other information.
WARTA
- NDELENG LANGGENG kanggo nangani piranti sensitif ELEKTROSTATIK
PILIH LOKASI MOUNTING
- Waca Sensor Kamar lan Lokasi Pemasangan Termostat lan Pandhuan Aplikasi Pangopènan for cautions, troubleshooting, and best practices.
CATETAN: Rampungake kabel kasar ing saben lokasi sadurunge nginstal sensor.
Mbusak BACKPLATE
- Turn the hex screw(1) clockwise into the sensor until the screw clears the cover.
CATETAN: The hex screw(2_ should remain in the backplate.
- Tarik tutup saka backplate.
SAMBUNGAN KABEL ETHERNET - Feed the Ethernet patch cable(3) from the Conquest controller through the center of the backplate(4).
CATETAN: Kabel patch Ethernet kudu maksimal 150 kaki (45 meter).
- Pasang backplate ing kothak listrik nggunakake sekrup sing kasedhiya.
CATETAN: If additional thermal insulation is needed, install the optional HPO-9002 gasket before installing the backplate.
Kanggo informasi luwih lengkap, ndeleng ing Room Sensor and Thermostat Mou
nting Location and Maintenance Application Guide. - Pasang kabel Ethernet 5 menyang jack modular 6 saka sensor.
INSTAL tutup SENSOR - Place the cover(7) over the top of the backplate(8) and swing it down.
CATETAN: Ati-ati aja jiwitake kabel Ethernet.
- Turn the hex screw(9) counterclockwise until it engages the cover.
OPERASI
- The STE-9000 Series NetSensor becomes operational after it is connected to a powered Conquest controller.
- CATETAN: To change setpoints or configuration, see the KMC Conquest Controller Aplikasi Guide.
- CATETAN: For continued maximum NetSensor efficiency, see the maintenance section in the Sensor Kamar lan Lokasi Pemasangan Termostat lan Pandhuan Aplikasi Pangopènan.
WARTA PENTING
- Materi ing dokumen iki mung kanggo tujuan informasi. Isi lan produk sing diterangake bisa diganti tanpa kabar.
- KMC Controls, Inc. makes no representations orwarranties with respect to this document. In no event shall KMC Controls, Inc. be liable for any damages, direct, or indirect, arising out of or related to the use of this document.
- Logo KMC minangka merek dagang kadhaptar saka KMC Controls, Inc. Kabeh hak dilindhungi undhang-undhang.
KONTAK
- Telpon: 574.831.5250
- FAX: 574.831.5252
- e-mail: info@kmccontrols.com
FAQ
Q: Which models are affected by the installation issue?
A: This issue affects all STE 9000 series NetSensors.
Q: What are the potential errors from a damaged printed circuit board?
A: Incorrect temperature and humidity readings may result from a damaged printed circuit board.
Dokumen / Sumber Daya
 |
KMC CONTROLS STE-9000 series NetSensor Damage from Incorrect Installation [pdf] Pandhuan pangguna STE-9000 series NetSensor Damage from Incorrect Installation, STE-9000 series, NetSensor Damage from Incorrect Installation, NetSensor Damage from Incorrect Installation, NetSensor Damage, from Incorrect Installation |