DFI EC70A-ADN Fanless Embedded System

Produk Overview

The EC70A-ADN is a fanless embedded system designed for various industrial applications.
It features a compact form factor and a range of I/O ports for connectivity.

Spesifikasi

• Sistem tanpa kipas Fanless
• Model: EC70A-ADN
• Port ngarep: HDD LED, Power LED, Antenna Hole, COM1, Mic-In, Line-Out, Power Button
• Port mburi: HDMI, Type-C DP Alt. Mode, USB 2.0, USB 3.2, LAN1~3, Grounding Hole, DC Jack

Pandhuan Panggunaan Produk

Njabut Cover Chassis

1. Ensure the system and connected devices are powered off and disconnect all cables.
2. Remove the screws securing the bottom cover and lift it upward to access the internal components.

Inserting a SO-DIMM Module

1. Daya mudhun sistem lan copot kabeh kabel.
2. Remove the heat shield screws to access the SO-DIMM socket.
3. Insert the memory card, aligning the notch and key, pressing firmly into the socket.
4. Ensure the clips snap into place and inspect the installation.

Nginstal Antena

1. Power off the system and disconnect all cables.
2. Remove the rubber plug covering the antenna hole on the front side of the system.
3. Connect the internal cable to the board’s antenna connector and attach the antenna securely.

Isi Paket

• 1 EC70A-ADN System Unit

Produk Overview

Ngarep View

1. LED HDD
2. Daya LED
3. Lubuk Antena
4. COM1
5. Mic-In
6. Line-Metu
7. Tombol Daya
   1. mburi View
8. HDMI 12
9. Type-C DP Alt. Mode
10. USB 2.0
11. USB 3.2

INSTALASI

Njabut Cover Chassis

Mangga maca lan tindakake pandhuan ing ngisor iki kanggo mbukak sistem.

1. Priksa manawa sistem lan kabeh piranti periferal liyane sing disambungake wis dipateni.
2. Copot kabeh kabel lan kabel daya.

Langkah 1:

• The 2 screws on the bottom of the system are used to secure the bottom cover to the chassis.
• Remove the screws and put them in a safe place for later use. Lift the bottom cover upward to open the system.

Langkah 2:

• The heat shield and the board can be easily accessed after the chassis cover is removed.

Inserting a SO-DIMM Module

Before installing the memory module, please read and follow the safety cautions below.

1. Priksa manawa PC lan kabeh piranti periferal liyane sing disambungake wis dipateni.
2. Copot kabeh kabel lan kabel daya.
3. Goleki soket SO-DIMM ing papan sistem.
4. Priksa manawa kedudukan ing kertu memori didadekake siji karo tombol ing soket.

Langkah 1:

• Remove the 3 screws of the heat shield and put them in a safe place for later use.
• Remove the heat shield, and the SO-DIMM socket is readily accessible.

Mangga tindakake langkah ing ngisor iki kanggo nginstal kertu memori menyang soket.

Langkah 2:

• Insert the memory card into the slot while making sure 1) the notch and the key are aligned, and 2) the nonconnector end rises approximately 45degrees horizontally. Press the card firmly into the socket while applying and maintaining even pressure on both ends.

Langkah 3:

• Pencet mburi kertu adoh saka soket mudhun nalika mesthekake kedudukan penylametan lan klip selaras minangka dituduhake dening garis burik ing ilustrasi. Yen kedudukan penylametan lan klip ora selaras, copot kertu lan lebokake maneh. Pencet kertu kabeh mudhun.

Langkah 4:

• The clips snap automatically and abruptly to the retention notches of the card, sounding a distinctive click, and lock the card in place. Inspect that the clip sits in the notch. If not, please pull the clips outward, release and remove the card, and mount it again.

Nginstal Antena

Sadurunge masang antena, priksa manawa ati-ati safety ing ngisor iki ditindakake.

1. Priksa manawa PC lan kabeh piranti periferal liyane sing disambungake wis dipateni.
2. Copot kabeh kabel lan kabel daya.

Langkah 1:

• There are antenna holes reserved on the front side of the system and covered by rubber plugs.
• Copot plug sadurunge masang antena.

Langkah 2:

• Connect the internal cable to the board’s antenna connector, screw the antenna connector through the antenna hole with washers and nuts, and screw on the antenna as illustrated below

INFO liyane

• DFI nduweni hak kanggo ngganti spesifikasi sawayah-wayah sadurunge rilis produk.
• QR iki bisa uga adhedhasar revisi produk.
• Kanggo dokumentasi lan driver liyane, bukak kaca download ing www.dfi.com/downloadcenter, utawa liwat kode QR ing sisih tengen.

FAQ

Q: Can I upgrade the memory in this system?

A: Yes, you can upgrade the memory by inserting compatible SO-DIMM modules following the provided instructions.

Q: How many USB ports are available on this system?

A: The system has USB 2.0 and USB 3.2 ports available for your connectivity needs.

Dokumen / Sumber Daya

DFI EC70A-ADN Fanless Embedded System [pdf] Pandhuan Instalasi EC70A-ADN Fanless Embedded System, EC70A-ADN, Fanless Embedded System, Embedded System, System

Referensi

• Manual pangguna