Cdtech TP300 Bluetooth Module Owner’s Manual

Cdtech TP300 Bluetooth Module

Swaraview
CDI-WC46600A-01 is a Wi-Fi + BLE module independently developed by Cdtech based on the ECR6600-ATS2L chip. ECR6600-ATS2L is a SoC chip designed for smart home IoT terminal devices, supporting Wi-Fi 802.11b/g/n/ax and BLE 5.1 protocols. It includes a power management module, power ampliifier, kurang swara amplifier, and transceiver switch. ECR6600-ATS2L adopts a RISC processor architecture, has ample storage space, rich peripheral interfaces, a more secure encryption mechanism, an on-chip FullMAC architecture, and a wider operating temperature range.

Karakteristik

Fitur Wi-Fi

• Supports IEEE 802.11 b/g/n/ax
• Supports Full MAC, including LMAC and UMAC
• Supports SoftAP, STA, and Wi-Fi direct connection mode
• Supports WMM QoS
• Supports 0.8/1.6/3.2 US security protection intervals
• Supports 802.11 ax MCS0 – MCS7
• The maximum bit rate reaches 150 Mbps
• Both uplink and downlink support MU-OFDMA (STA is supported)
• STA supports beamforming (STA acts as the Beamformer)
• Ndhukung Mid-amble
• Supports 20 M and 40 M bandwidth. 802.11ax only supports 20 M bandwidth.
• Supports dual carrier modulation (Dual Carrier Modulation, DCM)

Fitur BLE

• Supports BLE 5.1 protocol (does not support AOA/AOD)
• Supports single-device BLE connection
• Supports synchronous broadcasting and scanning
• Supports enhanced power control
• Output power up to +8 dBm
• Supports adaptive frequency hopping (AFH)
• Ndhukung ngirim lan nampa data bedo
• Ndhukung nganyari parameter sambungan
• Supports extensible data packet length
• Ndhukung enkripsi lapisan link
• Mendukung ping LE

The Wi-Fi subsystem and BLE subsystem share the radio part, including ADC/DAC/PLL. Wi-Fi and BLE can only have one working at a time.

Spesifikasi Umum

Pin description and PCBA size

Note: Method for downloading the module: VCC, GND, EN (pull-up), UART0_TX, UART0_RX, RESET_B (connected to the RTS of the serial port)

Module physical picture

Bill saka bahan

Karakteristik listrik

Direct-current characteristic

Suggested working conditions

Reflow soldering curve graph

Dirujuk menyang standar IPC / JEDEC.

• Suhu Puncak: <250°C
• Jumlah Kaping: ≤2 kaping

package figure

Pandhuan Packaging

1. 700 pcs

   • Each reel is loaded with 700 pcs (leave 20 empty pockets at both the front and back without components).

2. Perform vacuum packaging once the taping process is complete.

3. After vacuum packaging, place the taped reel into the inner box (700 pcs total per box).

4. 700pcs × 5 = 3500pcs

   • Each outer carton holds 5 inner boxes, for a total capacity of: $700\text{ pcs} \times 5 = 3500\text{ pcs}$.

WC46600A-01 is an ESD (Electrostatic Discharge) sensitive component. ESD or peak voltage may cause damage to the device. Although the WC46600A-01 has an internal ESD protection circuit, please handle it with care to avoid causing permanent damage or performance degradation.

Sertifikasi
Pandhuan integrasi kanggo produsen produk host miturut KDB 996369 D03 OEM Manual v01r01

Dhaptar aturan FCC sing ditrapake
CFR 47 FCC Part 15 Subpart C and Subpart C has been investigated. It is applicable to the modular transmitter.

Ketentuan Penggunaan Operasional Khusus
Antenna Placement Within the Host Platform The module is tested for mobile RF exposure use condition.. The transmitter module may not be co-located with any other transmitter or antenna. In the event that these conditions cannot be met (for example konfigurasi laptop tartamtu utawa co-lokasi karo pemancar liyane), banjur wewenang FCC ora dianggep bener lan ID FCC ora bisa digunakake ing produk final. Ing kahanan kasebut, integrator OEM bakal tanggung jawab kanggo ngevaluasi maneh produk pungkasan (kalebu pemancar) lan entuk wewenang FCC sing kapisah.

Prosedur Modul winates
Ora ditrapake

Tilak Desain Antena
Ora ditrapake

RF Exposure Pertimbangan
This device complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be mobile RF exposure use condition.

Jinis Antena lan Gain

• Antena ing ngisor iki wis disertifikasi kanggo nggunakake modul iki.
• Mung antena saka jinis padha karo gain padha utawa ngisor uga bisa digunakake karo modul iki.
• Jinis antena liyane lan/utawa antena gain sing luwih dhuwur bisa uga mbutuhake wewenang tambahan kanggo operasi.

Informasi Kepatuhan Labeling Produk Akhir
When the module is installed in the host device, the FCC ID label must be visible through a window on the final device or it must be visible when an access panel, door or cover is easily removed. If not, a second label must be placed on the outside of the final device that contains the following text:“Contains FCC ID:2AATP-TP300”. The FCC ID can be used only when all FCC compliance requirements are met.

Informasi babagan Mode Tes lan Syarat Tes Tambahan
This transmitter is tested in mobile RF exposure condition and any co-located or simultaneous transmission with other transmitter(s) class II permissive change re-evaluation or new FCC authorization. Host manufacturer installed this modular with single modular approval should perform the test of radiated emission and spurious emission according to FCC part 15C, 15.209, 15.207 requirements, only if the test result comply with FCC part 15C, 15.209, 15.207 requirement, then the host can be sold legally.

Pengujian tambahan, Part 15 Subpart B Penafian
This transmitter modular us tested as a subsystem and its certification does not cover the FCC Part 15 Subpart B rules requirement applicable to the final host. The final host will still need to be reassessed for compliance to this portion of the rules requirements if applicable. As long as all conditions above are met, further transmitter tests will not be required. However, the OEM integrator is still responsible for testing their end-product for any additional compliance requirements required with this modular installed.

Informasi Manual kanggo Pangguna Akhir
The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF module in the user’s manual of the end product which integrates this module. The host integrator must follow the integration instructions provided in this document and ensure that the composite system end product complies with the requirements by a technical assessment or evaluation to the rules and to KDB Publication 996369. The host integrator installing this module into their product must ensure that the final composite product complies with the requirements by a technical assessment or evaluation of the rules, including the transmitter operation, and should refer to guidance in KDB Publication 996369. OEM/Host Manufacturer Responsibilities: OEM/Host manufacturers are ultimately responsible for the compliance of the Host and Module. The final product must be reassessed against all the essential requirements of the FCC rule such as FCC Part 15 Subpart B before it can be placed on the US market. This includes reassessing the transmitter module for compliance with the Radio and RF Exposure essential requirements of the FCC rules

Cara Nggawe Owah-owahan - Wigati Penting
Yen kahanan kasebut ora bisa ditindakake (umpamaneampNanging, konfigurasi laptop tartamtu utawa co-lokasi karo pemancar liyane), banjur wewenang FCC ora dianggep bener lan ID FCC ora bisa digunakake ing produk pungkasan. Ing kahanan kasebut, integrator OEM bakal tanggung jawab kanggo ngevaluasi maneh produk pungkasan (kalebu pemancar) lan entuk wewenang FCC sing kapisah.

Pranyatan FCC

Piranti iki mung dimaksudaké kanggo integrator OEM ing kahanan ing ngisor iki

1. Antena kudu dipasang kanthi jarak 20 cm antarane antena lan pangguna.
2. Modul pemancar bisa uga ora ana karo pemancar utawa antena liyane.

• Module Antenna Type: 2.4GHz onboard FPC Antenna, 2.68 dBi peak gain.

Piranti iki tundhuk karo Part 15 saka Aturan FCC. Operasi tundhuk karo rong syarat ing ngisor iki:

1. Piranti iki bisa uga ora nyebabake gangguan sing mbebayani.
2. Piranti iki kudu nampa gangguan sing ditampa, kalebu gangguan sing bisa nyebabake operasi sing ora dikarepake.

Cathetan: Penerima dana ora tanggung jawab kanggo owah-owahan utawa modifikasi sing ora disetujoni kanthi jelas dening pihak sing tanggung jawab kanggo tundhuk. Modifikasi kasebut bisa ngilangi wewenang pangguna kanggo ngoperasikake peralatan kasebut.

CATETAN: Peralatan iki wis dites lan ketemu kanggo tundhuk karo watesan kanggo piranti digital Kelas B, miturut bagean 15 saka Aturan FCC. Watesan kasebut dirancang kanggo menehi pangayoman sing cukup marang gangguan sing mbebayani ing instalasi omah. Peralatan iki ngasilake panggunaan lan bisa mancarake energi frekuensi radio lan, yen ora dipasang lan digunakake miturut pandhuane, bisa nyebabake gangguan sing mbebayani kanggo komunikasi radio. Nanging, ora ana jaminan manawa gangguan ora bakal kedadeyan ing instalasi tartamtu. Yen peralatan iki nyebabake gangguan sing mbebayani kanggo panrima radio utawa televisi, sing bisa ditemtokake kanthi mateni lan nguripake peralatan kasebut, pangguna dianjurake kanggo nyoba mbenerake gangguan kasebut kanthi siji utawa luwih saka langkah-langkah ing ngisor iki:

• Reorient utawa pindhah antena panampa.
• Tambah pamisahan antarane peralatan lan panrima.
• Sambungake peralatan menyang stopkontak ing sirkuit beda saka sing panrima disambungake.
• Hubungi dealer utawa teknisi radio/TV sing berpengalaman kanggo njaluk bantuan.

The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF module in the user’s manual of the end product which integrates this module. The host integrator must follow the integration instructions provided in this document and ensure that the composite system end product complies with the requirements by a technical assessment or evaluation to the rules and to KDB Publication 996369. The host integrator installing this module into their product must ensure that the final composite product complies with the requirements by a technical assessment or evaluation to the rules, including the transmitter operation and should refer to guidance in KDB Publication 996369.OEM/Host manufacturers are ultimately responsible for the compliance of the Host and Module. The final product must be reassessed against all the essential requirements of the FCC rule, such as FCC Part 15 Subpart B, before it can be placed on the US market. This includes reassessing the transmitter module for compliance with the Radio and RF Exposure essential requirements of the FCC rules.

Pranyatan Eksposur RF
Peralatan iki tundhuk karo watesan cahya radiasi FCC sing ditemtokake kanggo lingkungan sing ora dikendhaleni. Peralatan iki kudu dipasang lan dioperasikake kanthi jarak minimal 20 cm antarane radiator lan awak