Home › ATOMSTACK › ATOMSTACK L2 Smart Z-Axis Module Installation Guide

ATOMSTACK L2 Smart Z-Axis Modul Pandhuan Instalasi

ATOMSTACK L2 Smart Z-Axis Modul

Manual instalasi adjuster otomatis dhuwur sumbu Z L2-5W/L2-10W/L2-20W/L2-40W

Cathetan: Gambar mung kanggo referensi, waca produk nyata. Kanggo informasi luwih lengkap, mangga pindai kode QR.

dhaptar

Metode instalasi sumbu Z

A5 PRO V2/A10 PRO V2

Bukak 4 pcs M4*6 counterclockwise kanggo mbusak panggeser

Pasang konektor khusus A5 Pro V2/A10 Pro V2
Kenceng 4 pcs M4*6

A20 PRO V2/A40 PRO V2

A6 Pro / A12 Pro / A24 Pro / X12 Pro / X24 Pro / E6 Pro / E18 Pro / E24 Pro / A6 Ultral / A12 Ultral / A24 Ultral / X12 Ultral / X24 Ultral A48 PRO/A48 Ultra ora perlu kanggo mindhah switch watesan

Langkah 1

Flip liwat engraver
Copot 2 ngawut-awut mati Papan ngalih watesan
Pindhah papan maju kanggo nyelarasake 2 bolongan
Kunci 2 ngawut-awut bali menyang Papan
Rampung
Flip liwat engraver

Metode instalasi laser terpadu

Langkah: 1 Copot 4 pcs M3 lan panggeser laser
Langkah: 2 Pasang panggeser laser kanthi 4 sekrup M3 sing dicopot saka langkah 1

Cathetan: Bukak tutup Piece mbenakake karo salib screwdriver ing toolkit pisanan, banjur nginstal laser panggeser kanggo A48 laser

Metode sambungan kabel

Cara instalasi laser
A5 PRO V2/A10 PRO V2/A20 PRO V2/A40 PRO V2

A6 Pro / A12 Pro / A24 Pro / X12 Pro / X24 Pro / E6 Pro / E18 Pro / E24 Pro / A6 Ultral/ A12 Ultral/A24 Ultral/X12 Ultral/ X24 Ultral

A5 PRO V2/A10 PRO V2/A20 PRO V2/A40 PRO V2

Cathetan: Nalika daya kanggo nggunakake Z-axis dhuwur otomatis adjuster, sampeyan mung perlu menet "fokus otomatis" tombol ing kothak kontrol kanggo fokus otomatis laser

A6 Pro / A12 Pro / A24 Pro / X12 Pro / X24 Pro / E6 Pro / E18 Pro / E24 Pro / A6 Ultral / A12 Ultral / A24 Ultral / X12 Ultral / X24 Ultral

Cathetan: Tampilan dibutuhake nalika nggunakake adjuster otomatis dhuwur sumbu Z, sampeyan kudu ngontrol saka mburi tampilan

layanan pelanggan: Kanggo kabijakan garansi sing rinci, bukak resmi websitus: www.atomstack.com Kanggo dhukungan teknis lan layanan, kirim email: support@atomstack.com
Produsen: Shenzhen AtomStack Technologies Co.,Ltd
alamat: 17th Floor, Building 3A, Phase II, Intelligent Park, No. 76, Baohe Avenue, Bip code: tret, Longgang District, Shenzhen, Guangdong, China
Pindai kode QR: UTAWA kode maca / barcode scanner utawa app karo scanner

Dokumen / Sumber Daya

L2 Smart Z-Axis Modul

Installation Guide · L2, L2 Smart Z-Axis Module, Smart Z-Axis Module, Z-Axis Module, Module

Referensi

Manual panggunamanual.tools

Published: July 13, 2024

Dianyari: Juli 14, 2024

Pitakonan lan jawaban

Helpful product questions tied to this manual. Each item links to the full Q&A page.

Pitakonan & Jawaban

Use this section to ask about setup, compatibility, troubleshooting, or anything missing from this manual.

🇺🇸 Robert ngandika:

23 April 2026 ing 12: 48
I have an ATOMSTACK A20 PRO V2 machine and have just purchased a L2 Z axis motorized drive ( BM AAS41A0125-AB ) and would like to hook it up but the cable attached to the unit has a connector which does not match any place on my machine . Where does it go to . In the instructions it looks like where the connection for the y motor is. Please clarify how to hook it up . Thank You Bob
🇺🇸 Robert asks I have an ATOMSTACK A20 PRO V2 machine and have just purchased a L2 Z axis motorized drive ( BM AAS41A0125-AB ) and would like to hook it up but the cable attached to the unit has a connector which does not match any place on my machine . Where does it go to . In the instructions it looks like where the connection for the y motor is. Please clarify how to hook it up . Thank You Bob

Manuals+ clarified question

Pitakonan

How do I connect the L2 Smart Z-Axis Module cable to an ATOMSTACK A20 PRO V2 machine?
Wangsulan

Kanggo nyambungake ATOMSTACK L2 Smart Z-Axis Modul marang Panjenengan A20 PRO V2, you must use the specific wiring method outlined in the manual for "V2" series machines. The connection does not plug directly into a spare port on the motherboard; instead, it typically involves an adapter or a specific bridge connection.

Miturut Section 05 — Cable connection method for the A20 PRO V2:

X-Axis Connection: The Z-axis module cable usually connects to the transfer board located on the X-axis carriage.

Y-Axis Motor Comparison: While the connector may look similar to a Y-axis motor plug, it is intended for the Z-axis control port. On V2 models, this is often a 4-pin or 6-pin connector located on the breakout board near the laser module mount.

Check for the Adapter: Ensure you are using the "Z-axis connection cable" included in the L2 kit (listed as item 4 in the 01-List). One end connects to the L2 module motor, and the other connects to the reserved Z-axis port on the machine's X-axis terminal.

If the connector physically does not fit any port on the X-axis carriage board, please verify if your kit included a small Papan adaptor utawa a Y-shaped splitter cable, as some V2 revisions require splitting the signal or using a specific conversion interface provided in the L2 box.
Read the full Q&A page
wangsulane
1. 🇺🇸 Robert ngandika:
  
  23 April 2026 ing 2: 31
  I don’t know what the transfer board is nor do I see anything on the x axis carriage. What is the x axis terminal ? I don’t see any extra ports anywhere .
  🇺🇸 Robert asks I don't know what the transfer board is nor do I see anything on the x axis carriage. What is the x axis terminal ? I don't see any extra ports anywhere .
  
  Manuals+ clarified question
  
  Pitakonan
  
  Where are the transfer board and X-axis terminal located on the ATOMSTACK L2 Smart Z-Axis Module?
  
  Wangsulan
  
  Based on the installation manual for the ATOMSTACK L2 Smart Z-Axis Modul, the components you are looking for are part of the cable connection setup (Section 05):
  
  Transfer Board: This is the small PCB (circuit board) located on the back or side of the X-axis carriage (the part that moves left and right). On many AtomStack models like the A6, A12, A24, and X24 series, this board is where the main ribbon cable connects.
  
  X-axis Terminal: This refers to the specific port on that transfer board. For the L2 module, you typically need to plug the Z-axis connection cable into the port labeled for the Z-axis or the auxiliary port on this board.
  
  Cathetan: If you do not see extra ports, ensure you are looking at the bali of the laser carriage assembly. On some older models (like the A5 Pro or V2 series), the connection method differs and may involve connecting directly to the main control box or using a specific adapter cable included in the L2 kit. Please verify your specific machine model, as the manual shows different wiring paths for the A5/V2 series versus the Pro/Ultra series.
  
  Read the full Q&A page
  wangsulane
  1. 🇺🇸 Robert ngandika:
    
    23 April 2026 ing 2: 55
    I do not see any PCB or any extra ports. Nor is there any adapters or splitters in the box.
    
    🇺🇸 Robert asks I do not see any PCB or any extra ports. Nor is there any adapters or splitters in the box.
    
    Manuals+ clarified question
    
    Pitakonan
    
    Where are the PCB, extra ports, adapters, or splitters for the ATOMSTACK L2 Smart Z-Axis Module?
    
    Wangsulan
    
    Based on the ATOMSTACK L2 Smart Z-Axis Module installation guide, the components included in the box (Section 01 - List) are:
    
    Z-axis height adjuster
    
    Laser slider
    
    A5/P/A10/A20/X20/S20 dedicated connector
    
    M3 * 6 ngawut-awut
    
    M4 * 5 ngawut-awut
    
    Z-axis connection cable
    
    Manual
    
    2.0/2.5 kunci Allen
    
    Obeng silang
    
    Regarding the PCB and Ports: The L2 module is designed to integrate with existing AtomStack frames. For many models (like the A6 Pro, A12 Pro, A24 Pro, etc.), the connection is made directly to the existing X-axis motor interface or the laser module's connection point using the provided Z-axis connection cable. There is typically no separate external PCB board included in this kit.
    
    Regarding Adapters/Splitters: The manual shows that for certain models (Section 05 - Cable connection method), you must unplug the original X-axis motor cable and connect it to the Z-axis module's interface, or use the dedicated connector provided in the kit. If your specific machine model is not listed in the manual (A5, A10, A20, A6 Pro, etc.), you may require a specific adapter not included in the standard L2 package. If these items are missing from your specific kit, it is recommended to contact support@atomstack.com kanggo verifikasi.
    
    Read the full Q&A page
    wangsulane
    1. 🇺🇸 Robert ngandika:
      
      23 April 2026 ing 3: 23
      
      Now what do I do ?
      
      🇺🇸 Robert asks Now what do I do ?
      
      Manuals+ clarified question
      
      Pitakonan
      
      What are the next steps after installing the ATOMSTACK L2 Smart Z-Axis Module?
      
      Wangsulan
      
      Once you have physically mounted the ATOMSTACK L2 Smart Z-Axis Module and connected the cables as shown in the manual, you must configure your software to recognize the new hardware. Follow these steps:
      
      Verifikasi kabel: Ensure the Z-axis connection cable is securely plugged into the module and the corresponding port on your laser engraver's motherboard (refer to Section 05 of the manual for your specific model).
      
      Konfigurasi Piranti Lunak: Open your laser control software (LightBurn or LaserGRBL). You may need to enable the Z-axis in the device settings. In LightBurn, go to Setelan piranti and ensure 'Enable Z-Axis' is toggled on.
      
      Fokus: The L2 module is designed for automatic or simplified focusing. Use the control panel or software commands to move the Z-axis up and down to verify smooth movement before starting a project.
      
      Batas Ngalih: If you are using models like the A6 Pro, A12 Pro, or A24 Pro, the manual notes that you do not need to relocate the limit switches.
      
      If the module is not moving, double-check that the 2-pin or 4-pin connectors are not reversed and that your machine's firmware is up to date.
      
      >
      
      Read the full Q&A page
      
      wangsulane

Takon Pitakonan Cancel question

Topik sing gegandhengan

Modul L2