MIBOXER DMX512 4 Channel Konstan Voltage lan RDM Decoder

Pandhuan Panggunaan Produk

• Long press M and key in the same time for 2s to prepare for setting up system parameters.
• You can configure decode mode, grey level, output PWM frequency, output brightness curve, default output level, and automatic blank screen. Short press M key to switch between the six items.
• To set the decode mode, short press or key to switch between 1/2/4 channel decode mode (d-1, d-2, or d-4).
• To enter DMX mode, short press M key. When the display shows 001~512, you are in DMX mode.
• Press or key to change the DMX decode start address (001~512).
• Long press for fast adjustment. If there is a DMX signal input, the device will automatically enter DMX mode.
• Each D4 DMX decoder occupies 4 DMX addresses when connecting to the DMX console.

Fitur

• Patuhi protokol standar DMX512.
• Digital numeric display, set the DMX decode start address by buttons.
• Fungsi RDM bisa mujudake interkomunikasi antarane master DMX lan decoder.
  • Kanggo example, alamat decoder DMX bisa disetel dening DMX master console.
• 1/2/4 DMX saluran output dipilih.
• 16bit (65536 levels) /8-bit (256 levels) grey level selectable.
• PWM frequency 250/500/1000/2000/4000/8000/16000/32000Hz selectable.
• Kurva peredupan logaritma utawa linear bisa dipilih.
• Stand-alone RGB/RGBW mode and 4-channel dimmer mode selectable, which be controlled by buttons with built-in programs, instead of DMX signal.
• Over-heat / Over-load / Proteksi sirkuit cendhak, pulih kanthi otomatis.
• Kasedhiya ing putih utawa ireng.

Parameter teknis

Input lan Output

• Input voltage: 12-48VDC
• Input saiki: 20.5A
• Output voltage: 4 x (12-48)VDC
• Output current: 4x5A@12/24V 4x4A@36/48V
• daya output
  • 4x60W@12V
  • 4x120W@24V
  • 4x144W@36V
  • 4x192W@48V
• Tipe Output: Vol konstantage

Lingkungan

• Operation temperature: Ta: -30 OC ~ +55 °C
• Case temperature (Max.): Tc: +75 °C
• Peringkat IP: IP20

Warranty lan Proteksi

• Garansi: 5 taun
• pangayoman
  • Polaritas Reverse
  • Over-heat (>95°C start)
  • Over-loading
  • Sirkuit cendhak

Safety lan EMC

• EMC standard: EN IEC 55015/ EN IEC 61547
• Safety standard: EN 61347-1/-2 EN 62493
• Certification: CE RoHs FCC

Paket

• Ukuran: L120 x W78 x H55 mm
• Bobot reged: 0.162kg

Struktur Mekanik lan Instalasi

Wiring Diagram

Cathetan:

1. Sinyal DMX amplifier is needed if more than 32 decoders are connected, or use overlong signal line is used, signal ampLification ngirim ora luwih saka 5 kaping terus-terusan.
2. Yen efek mundur amarga garis sinyal sing luwih dawa utawa kualitas garis sing ora apik, coba sambungake resistor terminal 0.25W 90-120Ω ing pungkasan saben baris sinyal DMX.
3. When display 1OL,2OL,3OL,4OL, correspond to 1,2,3,4 channel overload alarm.
   When displaying OHA, the overheat alarm.

Operasi

Setelan parameter sistem

• Long-press M and ◀ key in the same time for 2s, prepare for the setup system parameter: decode mode, grey level, output PWM frequency, output brightness curve, default output level, and automatic blank screen. Press M key to switch six item.
• Decode mode: short-press ◀ or ▶ key to switch 1/2/4 channel decode mode(“d-1″,”d-2” or “d-4”).
  When set as 1 1-channel decode, the decoder occupies only 1 DMX address, and four channels output the same brightness of this DMX address.
• Grey level: short press ◀ or ▶ key to switch 8bit(“b08”) or 16 bit(“b16”). Choose 16-bit if the DMX master supports 16-bit.
• Output PWM frequency: short press ◀ or ▶ key to switch 250Hz(“F02”), 500Hz(“F05”), 1000Hz(“F10”), 2000Hz(“F20”), 4000Hz(“F40”), 8000Hz(“F80”), 16000Hz(“F16”) or 32000Hz(“F32”).
• Higher PWM frequency will cause lower output current, higher power noise, but more suitable for camera(No ickers for video).
• When PWM frequency > 8000Hz, it is necessary to reduce the output current per channel (4x3A@12-48V at 16000Hz; 4×2.5A@12-24V and 4x2A@36-48V at 32000Hz)
• Output brightness curve: short-press press ◀ or ▶ key to switch linear curve(“C-L”) or the logarithmic curve(“C-E”).
• Default output level: set the output level when no DMX input signal. short press ◀ or ▶ key to switch maintain DMX output(“d- -“) or output default level (“d00” to “dFF”, 0-100%), long press ◀ or ▶ key to change output default level.
• Automatic blank screen: short-press press ◀ or ▶ key to switch enable (“bon”) or disable(“boF”) automatic blank screen.
• Pencet dawa tombol M kanggo 2 detik utawa wektu entek 10 detik, metu saka setelan parameter sistem.

Cathetan: Saliyane setelan operasi tombol manual, paramèter sistem ing ndhuwur uga bisa disetel dening fungsi RDM.

Mode DMX

• Press M key when the display shows 001~512, enter DMX mode.
• Press ◀ or ▶ key to change the DMX decode start address(001~512), long-press for fast adjustment.
• Yen ana input sinyal DMX, bakal mlebu mode DMX kanthi otomatis.
• DMX Dimming: Each D4 DMX decoder occupies 4 DMX addresses when connecting the DMX console.
• Kanggo example, the default start address is 1, their corresponding relationship in the form:

Konsol DMX	DMX Decoder Output
CH1 0-255	CH1 PWM 0-100% (LED R)
CH2 0-255	CH2 PWM 0-100% (LED G)
CH3 0-255	CH3 PWM 0-100% (LED B)
CH4 0-255	CH4 PWM 0-100% (LED W)

Mode RGB/RGBW mandiri

• Ketik mode RGB/RGBW dewekan mung nalika sinyal DMX pedhot utawa ilang.
• Press M key when the display shows P01~P30, enter stand-alone RGB/RGBW mode.
• Press ◀ or ▶ key to change the dynamic mode number (P01~P30).
• Saben mode bisa nyetel kacepetan lan padhange.
  • Pencet dawa tombol M kanggo 2 detik, nyiapake kacepetan mode persiyapan, padhang, padhang saluran W.
  • Short press M key to switch between three items.
  • Press ◀ or ▶ key to setthe  value of each item.
  • Kacepetan mode: 1-10 tingkat kacepetan (S-1, S-9, SF).
  • Mode padhange: 1-10 tingkat padhange (b-1, b-9, bF).
  • W channel padhange: 0-255 tingkat padhange (400-4FF).
  • Pencet dawa tombol M kanggo 2 detik, utawa wektu entek 10 detik, metu setelan.

Mode dimmer mandiri

• Ketik mode dimmer dewekan mung nalika sinyal DMX pedhot utawa ilang.
• Short press M key short, when the display shows L-1~L-8, enter stand-alone dimmer mode.
• Press ◀ or ▶ key to change the dimmer mode number(L-1~L-8).
• Saben mode dimmer bisa nyetel padhange saben saluran kanthi mandiri.
  • Long press M key for 2s, prepare for setup four the four-channel brightness.
  • Short press M key to switch four channels (100~1FF, 200~2FF, 300~3FF, 400~4FF).
  • Press ◀ or ▶ key to set the brightness value of each channel.
  • Pencet dawa tombol M kanggo 2 detik, utawa wektu entek 10 detik, metu setelan.

Mulihake parameter standar pabrik

• Long press ◀ and ▶ key for 2s, restore factory default parameters, and display”RES”.
• Factory default parameter: DMX decode mode, DMX decode start address is 1, four-channel decode, 8 bit grey level,
  2000Hz PWM frequence output, logarithmic brightness curve, output 100% level when no DMX input,
  RGB mode number is 1, dimmer mode number is 1, disable automatic blank screen.

Dhaptar Mode Ganti RGB

Ora.	jeneng	Ora.	jeneng	Ora.	jeneng
P01	abang statis	P11	Strobo ijo	P21	Merah kuning mulus
P02	Ijo statis	P12	Strobo biru	P22	Green cyan mulus
P03	Biru statis	P13	Strobo putih	P23	Biru ungu mulus
P04	Kuning statis	P14	RGB strobo	P24	Biru putih mulus
P05	Cyan statis	P15	7 warna strobo	P25	RGB+W mulus
P06	Ungu statis	P16	Abang luntur lan metu	P26	RGBW mulus
P07	Putih statis	P17	Ijo luntur lan metu	P27	RGBY mulus
P08	RGB mlumpat	P18	Biru luntur lan metu	P28	Kuning cyan ungu mulus
P09	7 werna lompat	P19	Putih luntur lan metu	P29	RGB mulus
P10	Strobo abang	P20	RGBW fade in and out	P30	6 warna mulus

Setelan Curve Dimming

Analisis Malfungsi & Ngatasi Masalah

Malfunctions	Nimbulaké	Ngatasi masalah
Ora ana cahya	1. Ora ana daya. 2. Sambungan sing salah utawa ora aman.	1. Priksa daya. 2. Priksa sambungan.
Salah werna	1. Salah sambungan kabel R / G / B / W. 2. DMX kesalahan alamat decode.	1. Sambungake maneh kabel R / G / B / W. 2. Set the correct decode address.
Intensitas ora rata antarane ngarep lan mburi, kanthi voltage nyelehake	1. Kabel output dawa banget. 2. diameteripun Wire cilik banget. 3. Kakehan ngluwihi kemampuan sumber daya. 4. Overload ngluwihi kemampuan controller.	1. Ngurangi pasokan kabel utawa daur ulang. 2. Ganti kabel sing luwih amba. 3. Ganti sumber daya sing luwih dhuwur. 4. Tambah daya repeater.

FAQ

Apa aku kudu sinyal DMX amppengangkat?

Sinyal DMX amplifier is needed if more than 32 decoders are connected or if an overlong signal line is used. Signal ampLification ngirim ora ngluwihi 5 kaping terus-terusan.

How do I address channel overload alarms?

If you see displays like 1OL, 2OL, 3OL, or 4OL, they correspond to 1, 2, 3, or 4 channel overload alarms respectively. When OHA is displayed, it indicates an overheat alarm.

What should I do for recoil effects?

If recoil effects occur due to a longer signal line or poor line quality, try connecting a 0.25W 90-120 terminal resistor at the end of each DMX signal line.

Dokumen / Sumber Daya

MIBOXER DMX512 4 Channel Konstan Voltage lan RDM Decoder [pdf] Manual Pamilik D4, DMX512 4 Channel Constant Voltage lan RDM Decoder, DMX512, 4 Channel Konstan Voltage lan RDM Decoder, Konstan Voltage lan RDM Decoder, Voltage lan RDM Decoder, RDM Decoder, Decoder

Referensi

• Manual pangguna